Reset ABS BLEEDING on 2015 Chevrolet Suburban by Launch ThinkDiag

It’s tested ok to reset ABS bleeding for 2015 Chevrolet Suburban using Launch ThinkDiag OBD2 diagnostic tool.

Car: 2015 Chevrolet Suburban (light duty truck)

Thinkdiag Reset Abs Bleeding 2015 Suburban 1

Device:Launch THINKCAR ThinkDiag OBD2 full system code reader

Thinkdiag Reset Abs Bleeding 2015 Suburban 2
http://www.obdiitool.co.uk/wholesale/thinkdiag-obd2-full-system.html
Procedures:
Install ThinkDiag APP on Android or IOS smart phone
Plug the ThinkDiag device into OBDII port in your vehicle until the green light appears
Turn on the ignition
Run ThinkDiag APP
Press the second icon at the bottom left of the APP screen to enter ThinkStore page

Thinkdiag Reset Abs Bleeding 2015 Suburban 3

Press “…” to show full purchased software

Thinkdiag Reset Abs Bleeding 2015 Suburban 4

There are two ways to reset ABS bleeding:

1.Select GM car make

Thinkdiag Reset Abs Bleeding 2015 Suburban 5

2.Select RESETBLEED function

Thinkdiag Reset Abs Bleeding 2015 Suburban 6

Here we choose the No.2 method to operate

Connect Bluetooth automatically

Select car manufacturer: GM

Thinkdiag Reset Abs Bleeding 2015 Suburban 7

Make sure turn on the ignition switch

Pay attention to the info:

If the first bit of the VIN is the L letter, please select path: CHINESECAR->SGM

Press [OK] enter GM software

Press [Cancel] exit

Just press OK to continue-

Tap Manually Select (Via Model)-> LD Trk, MPV, Incomplete-> Chevrolet Truck-> Suburban-> 2015-2018

And it will read out the car year

Thinkdiag Reset Abs Bleeding 2015 Suburban 8Thinkdiag Reset Abs Bleeding 2015 Suburban 9Thinkdiag Reset Abs Bleeding 2015 Suburban 10Thinkdiag Reset Abs Bleeding 2015 Suburban 11Thinkdiag Reset Abs Bleeding 2015 Suburban 12

The ABS bleeding reset instructions will display on the screen, just follow it to operate:

1.To perform the automated bleed and vehicle learn procedures. Follow the service manual and equipment manufacturer’s instructions.Connect the required brake bleed equipment Connect battery charger to 12V battery Turn ignition on Place transmission in the Park or Neutral position. Note: ignition must remain in the run position during the entire process.

2.Connect bleeder ball to vehicle and set to 300 kpa. Note: Do not open any bleeder screw until instructed.

3.Stop vehicle. This test cannot be run while moving Configuring brakes bleeding system!

They’re sending pressure through the line to clear out all the air, you’re going to hear this about four separate times so it’s going to happen on the front right and then front left, back right and back left.

Thinkdiag Reset Abs Bleeding 2015 Suburban 13

The notification is letting us know that the traction control was on and off

Thinkdiag Reset Abs Bleeding 2015 Suburban 14 Thinkdiag Reset Abs Bleeding 2015 Suburban 15

Once clear all four of these in that notification will be gone

Follow the prompts to reset automated bleed-left front/rear, bleed-right rear

Thinkdiag Reset Abs Bleeding 2015 Suburban 16 Thinkdiag Reset Abs Bleeding 2015 Suburban 17Thinkdiag Reset Abs Bleeding 2015 Suburban 18 Thinkdiag Reset Abs Bleeding 2015 Suburban 19Thinkdiag Reset Abs Bleeding 2015 Suburban 20 Thinkdiag Reset Abs Bleeding 2015 Suburban 21

Finish resetting ABS bleeding

Thinkdiag Reset Abs Bleeding 2015 Suburban 22

Check more car models which can work with Launch ThinkDiag, please visit the official website

It’s very easy to do. Just select the corresponding product, car manufacturer, model and year to search directly.

That’s all!