How to Save & Print Vehicle Diagnostic Data on Foxwell Scanners?
OBD2 Code Scanner / September 29, 2021

Question How do I save these GM vehicle fault codes from Foxwell NT530 to print out? Please help me.   Operating Steps Here is taking Foxwell NT624 Elite Automater Pro as an example. The procedure applies to most Foxwell scanners such as Foxwell NT650 Elite, NT680 Pro, etc.   Step1. Save Data File Follow the 2 paths below to save vehicle data files on Foxwell tool: EOBD >> Automatic selection >> Save Read codes >> Stored codes >> Save   Step2. Check Data File Follow the path to check if data files are saved successfully. Data manager >> Fault codes >> EOBD   Step3. Transmit Data Go to “Update”, connect Foxwell tool with PC via USB cable. Wait for a while until you can find out the “EOBD” file.   Step4. Print Diagnostic Data Log in Foxwell software, follow the path to print. Data Manager >> EOBD >> Report >> Print   Completed! Hope this is helpful. https://www.obdiitool.co.uk/

Solution: Lonsdor K518ISE/K518S “Device fault26” Error
Car Key Programmer / September 22, 2021

How to solve Lonsdor K518ISE/ Lonsdor K518S Key Programmer “Device fault26” error? This is a guide to solve the problem.   Solution Hold and press 2 buttons marked in red meanwhile, you’ll go access to the interface.   Press “Factory Setting”. Lonsdor K518 will show a prompt: “This will uninstall all apk, and format all user data, also the device will automatically restart and return to factory settings. Please be careful!!!”. Press “OK” and wait for about 1 minute.   Press “Repair”. A warning displays: “This operation will clear apk related data and reinstall, please operate carefully!!!”. Press “OK”.   Follow the path to find a repair file: Android desktop >> Circle button >> File manager >> Internal storage >> emulated >> 0 Note: if do not find the file, please connect Lonsdor K518 to a PC to put the file in.   Press repair file. A install blocked prompt shows: For security, your tablet is set to block installation of apps obtained from unknown source. Press “Settings >> Unknown sources >> OK”.   You’ll come back to same interface. Press repair file again. And then “Next >> Install >> Open”.   Connect Lonsdor K518 to WiFi, press “Update >>…

Maserati Oil Reset & EPB Reset Affordable Tool: Obdstar X200 Pro2
Car Diagnostic Tool / September 15, 2021

Obdstar X200 Pro2 is the most affordable service tool to perform oil reset & EPB reset for Maserati. Follow the demonstration below to learn how to do.   How to do 2017 Maserati Levante oil reset via Obdstar X200 Pro2? Connect X200 Pro2 with OBD, press Service >> All >> Oil/ service reset >> Oil/ service reset V32.49 >> Europe >> Maserati >> Levante >> 2017 >> IPC   Please switch on the ignition, and switch off the engine!   Reset success.   Simple and fast to be done! For 2018 Maserati, you’ll need a 12+8 Universal Adapter as well   How to do 2017-2018 Maserati Ghibli EPB reset via Obdstar X200 Pro 2? Connect X200 Pro2 Reset Tool with OBD, press Service >> All >> EPB(PBM) >> EPB(PBM)V30.82 >> Europe >> Maserati >> Ghibli M157 >> 2017-2018 >> Activate maintenance   Please turn on ignition, and shut down engine. Be very careful to proceed with work on the vehicle, the chassis may move or the engine may start.   Reset success. Done! Obdstar X200 Pro2 can also support some 2020 car models. For specific details, please contact us. https://www.obdiitool.co.uk/

How to Refresh BMW F Series 6HP EGS with Yanhua Mini ACDP?
Car Key Programmer / September 8, 2021

Yanhua Mini ACDP BMW + Module 11 can support to refresh BMW F series 6HP EGS on bench without soldering, this is a guide to show the operation process.   Procedure   Installation Preparation Prepare parts: ACDP, OBP+ICP adapter, EGS interface board & EGS module.   Connect EGS interface board & EGS module: Aim the 6HP end label point on interface board with the EGS interface label point during installation.   Short the jumper cap to the “CAN-R-Join”, connect all parts together. Refresh BMW 6HP EGS Open Mini ACDP app, click BMW >> EGS refresh >> 6HP data refresh(supports F chassis) >> Data refresh >> OK   Check info, click “Continue” It starts reading data…   OK >> Save >> OK Data file saved success. Read data is completed.   Click “Continue” to start write data.   Note: Start writing data. It is forbidden to unplug the ACDP and keep steady power supply to ACDP during the process! If the device disconnect, please unplug the ACDP after disconnection 15 mins, the ACDP will automatically complete the writing! Click “OK” to continue. It is writing data, please wait…   Data refresh is completed. It’ll show the backup path automatically. Done!  …

How to Use 2M2 Magic Tank to Cut Ford FO21 Key by Bitting?
Auto Locksmith Tool / September 1, 2021

This is a quick guide on how to use 2M2 Magic Tank Key Cutting Machine to cut a Ford FO21 key by bitting. The operation requires to get or decode the biting codes of working key before cutting. Connect MagicTank app with machine, press Cut by bitting >> Vehicle key >> FO21 >> Input bitting codes: 231432 >> Cut Please confirm whether it is a 2.0 milling cutter. Confirm Press “Play” button, it’ll show the clamp and key blank installation steps before cutting. Press “Cut” once installation was done. 2M2 Magic Tank starts cutting… The machine will process it automatically, just wait for finishing. Clean iron fillings when machine completed. Take out the key to have a try. It can switch the lock. Done! Ford FO21 key cutting via 2M2 Magic Tank is actually smart and easy, no need too many tedious steps. https://www.obdiitool.co.uk/  

无觅相关文章插件,快速提升流量