CG AT200 Programmer V1.5 Update 432 ECUs, TC1793S & TC1793 wiring diagram
ECU Chip Tuning Tool / September 16, 2019

CG AT200 Programmer V1.5 update with detailed table. 1.Can read and write MSD80 ISN and MSD81 ISN. Add the wiring diagrams for TC1793 and TC1793S 3.Add TC1767 ECU programming 4.AT200 V1.5 update 432 ECUs programming. TC1793 Car Name Series Engine ECU ECU Alfa Romeo 4C 960 1750 TBI 960.A1.000 240 BOSCH MED17.3.3 Giulia 952 2900 Twin Turbo 670050436 510 BOSCH MED17.3.5 2200 Multijet 55266388 150 BOSCH EDC17C69 ver3 2200 MUltijet 55266388 136 BOSCH EDC17C69 ver3 2200 MUltijet 55266388 209 BOSCH EDC17C69 ver3 Giulietta 940 1750 TBI 960.A1.000 240 BOSCH MED17.3.3 2000 JTDM 2 940.B4.000 175 BOSCH EDC17C69 ver1 Stelvio – 2900 Twin Turbo 670050436 510 BOSCH MED17.3.5 Aston Vantage IV 4000 M177 510 BOSCH MED17.7.5 Audi A3 8P 1400 TFSI e-tron CUKB 150 BOSCH MED17.1.21 A4 B9 2000 TFSI quattro CPMB 220 BOSCH MED17.1.10 2000 TFSI quattro flexible fuel CPMB 220 BOSCH MED17.1.10 2000 TFSI 190 BOSCH MED17.1.10 A5 8F/8T 2000 TFSI quattro CPMB 220 BOSCH MED17.1.10 2000 TFSI quattro flexible fuel CPMB 220 BOSCH MED17.1.10 A6 C7 3000 TDI 218 BOSCH EDC17CP54 3000 TDI quattro 218 BOSCH EDC17CP54 A7 4G 3000 TDI 313 BOSCH EDC17CP54 3000 TDI Ultra BOSCH EDC17CP54 Q5 8RB 2000 TFSI quattro CPMB 220 BOSCH MED17.1.10…

Xhorse Condor XC-Mini Plus User Manual: Installation, Update online
Auto Locksmith Tool / September 15, 2019

This article is available with cutter/clamp installation and online update instructions on Xhorse Condor XC- Mini Plus key cutting machine.   Installation instruction  -How to install cutter on Condor XC-Mini ii -How to uninstall cutter on Condor XC-Mini ii -How to install clamp on Condor XC-Mini ii   Online update    -How to update on Xhorse APP   In detail…   Installation instruction How to install cutter on Condor XC-Mini ii?   Step 1: Put the cutter into the mounting hole and make sure the cutter goes to the limit of top Step 2: Use the cutter tightening wrench to clockwise fix the cutter.   How to uninstall cutter on Condor XC-Mini II? Step 1: Counter-clockwise unscrew the cutter manually Step 2: Take the cutter off when it is loose   How to install clamp on Condor Mini Plus? Step 1: Loosening the clamp tightening wrench by turning it counter-clockwise to the left Step 2: Select the correct clamp and slide in the clamp to the clamp holder and push it to the limit of left Step 3: After the clamp is put in the clamp platform, turn the clamp tightening wrench clockwise for fix it   XC-Mini Plus clamps…

iProg+ Pro V77 Free Download, Installation on Win7
ECU Chip Tuning Tool / September 13, 2019

Iprog ECU programmer has been updated to V77. Check the free download link and installation guide below.   Iprog+ V77 ECU Programmer Free Download!hMxViSZJ!flDyz5MqXAhLHldDZ9EIII_b_CTPQj3Ansuraw12rP8 Language: English, Russian How to install iprog pro v77 on window 7?   Procedure: Go to DVD/CD-RW Drive (E disk) Open “Iprog 2019+ v77” You will see: 7z1900-32bit 7z1900-64bit Iprog+77.exe View the computer is 32 bit or 64 bit Select the corresponding file to install Copy “iProg+_2019_00001″ and paste it on the desktop Right click on “iProg+_2019_00001″, select “7-zip” to extract. Go to Computer-> “Device Manager” Right click on “iProg universal programmer” Select “Update Driver software” Select “Browse my computer for driver software” and click “OK” Search for driver software in the corresponding location Click “Next” to continue Select “Install this driver software anyway” to install iProg+ universal programmer has been installed successfully Open iProg Pro version 77 Come to main menu Adapter _test AIRBAG CAR DASHBOARD EEPROM Log MCU OTHER: CAN_SCAN.bir, CAN_SCAN_proba.bir   1.iProg+ V77 clone dashboard functions (read km, write a new km on many cars). Take “Toyota Avensis Denco 93c46.ipr mileage correction for example. Click OLD KM to show the current KM is 122040 Change the KM to 2560 and click “WRITE NEW KM”…

Autel MaxiCOM MK908P Customer Unbiased Reviews
Car Diagnostic Tool / September 11, 2019

Autel MaxiCOM MK908P is an evolutionary smart solution for specialized automotive diagnosis. Here have collected some customer feedbacks. Hope can give you some advices.   Review 1: Has wide vehicle coverage I have ever used MK908P scanner on Ford, Honda and VW etc. and there is nothing wrong, all works as described. It scans the car and knows exactly what you’re working with.  Highly recommend to the people looking for a diagnostic tool with wide vehicle coverage.   Review 2: This diagnostic tool works flawlessly Absolutely a good scanner. This diagnostic tool works flawlessly. It’s well worth the cost. I run a service department at a new car dealership and it has helped us greatly with used car inventory and customers who bring us other make vehicles   Review 3: the best smart scan in the market now This is a phenomenon, the best smart scan tool, I love it to bits, the updates are free, easy to download, well done Autel, I can’t believe how easy it is to use…. I highly recommend this to anyone who is a serious Tech … I used it on a Mercedes W211 E320 …and pulled 37 modules just like that ….unbelievable !…

Free download Chinese clone kess v2 5.017 SD card image
ECU Chip Tuning Tool / September 10, 2019

Chinese clone kess v2 5.017 with ksuite 2.47 has ‘wake up error’ and formatted the sd card, need the 5.017 SD card image, where to download the reliable source. There are two solutions below.   1st Solution: you only need a new SD card and this manual. works with every SD and every CID. 1). How to do read an SD card for Kess 5.017 or create a new one? 128 MB XOR!kRxTwQxZ!Vw6g3ROBHr9w7aboGEe97UPIbv2ruVOvlLIZaH1HPDY Zip Password = “kess5017”   Note: Only Kess 5.017 or 5.028, not for 3.099 etc.   2). How to create a new SD card? Firstly, download WinHex and XorFiles v1.0 Insert your Original SD-Card to Cardreader on PC. Run WinHex, press F9 open Disk, read your SD-card. Mark 208Bytes = 13 lines from 0x00000270 to 0x0000033F. Copy 13 lines to new file. Open in WinHex my Keyfile “128 MB XOR Key01-13.img” Search and replace line 1 in your Keyfile with all line1 lines in “128 MB XOR Key01-13.img” Search and replace line 2 in your Keyfile with all line2 lines in “128 MB XOR Key01-13.img” ………………………….. Search and replace line 13 in your Keyfile with all line13 lines in “128 MB XOR Key01-13.img” Save…

OBDSTAR X300 DP Plus Test Reports: VW NEC-24C64, 2018 Hyundai ix35, 2018 Fiat Doblo
Car Key Programmer / September 9, 2019

(9 September, 2019) Have collected some test reports on VW/ Hyundai/ Fiat Doblo with OBDSTAR X300 key master DP Plus.   Price: 1,443.16 euro free shipping (full version C package)   Test reports: VW NEC-24C64 AKL: program new key- OK 2018 Hyundai ix35 8A: program smart key- OK 2018 Fiat Doblo: read Pin Code and add new key- OK

CGDI Prog BMW Test Report: Works perfectly on CAS3+/ CAS4+
Car Key Programmer / September 8, 2019

CGDI prog BMW MSV80 is a good car key programmer for BMW. It supports key programming for BMW cas1/cas2/cas3, and supports key matching and all key lost for cas4 /cas 4+. Here have collected two test reports on CAS3+ and CAS4+ below.   Purpose: To check if CGDI Prog BMW can program new key to CAS3+/ CAS4+ or not   Test:   Test 1: CGDI BMW add new key to CAS3+ all keys lost- OK Note: It’s more convenient to work with the cables (DIY by professional technician), no need to dismantle or drill.   Step 1: Click “Read DME ISN” or select the corresponding ECU to read   Step 2: Read CAS key info by CGDI prog Get ISN code and save Note: Need to downgrade to CAS3   Step 3: Plug the blank into CGDI prog BMW coil Confirm the key is smart key or not Wait to program the key process completing   Program key success   Step 4: Use the new key programmed to test   Test 2: CGDI BMW MSV80 add new key to CAS4+ all keys lost- OK Step 1: Read CAS4+ Immobilizer data by CG PRO 9S12 Note: Don’t forget to make backup…

Read MG350 BCM 95160 Pin Code with OBDSTAR X300 DP PLUS via EEPROM
Car Key Programmer / September 2, 2019

How-to: Extract MG350 95160 pin code by OBDSTAR  X300 DP Plus key programmer. Remove eeprom IC 95160 and solder it to P001 eeprom 3-in-1 adapter In X300 DP Plus, select Immobilizer->PIC/Freescale-> PIC/Freescale Adapter V34.04->EEPROM->Read Pin Code->MG->MG5->BCM 95160-> Make sure OBDSTAR P001 programmer is connected with X300 DP Plus Reading data in process Read data success. Save data. Read 4-digit pin code success Done. You can read MG350 pin code with OBDSTAR X100 Pro and EEPROM/PIC adapter as well.